Descripción

Telephony

VoIP to PSTN (USA) Service Call Origination and TerminationPSTN (USA) to VoIP Service Call Origination and Termination
Single or Dual Stage Dialing
Service Authentication via PIN, Digest, Caller ID (Bellcore Type 1)
Per Call Authentication and Associated Routing
Least Cost Routing Support
Impedance Agnostics – 8 Settings
Call Waiting, Cancel Call Waiting, Call Waiting Caller ID Detection (Bellcore Type 1)
Caller ID with Name/Number (Multi-national Variants)
Caller ID Blocking
Call Forwarding to PSTN or VoIP Service: No answer, Busy, All
Do Not Disturb
Call Transfer
Three-way Conference Calling with Local Mixing
Message Waiting Indication – Visual and Tone Based
Call Return
Call Back on Busy
Call Blocking with Toll Restriction
Delayed Disconnect
Distinctive Ringing – Calling and Called Number
Off-hook Warning Tone
Selective/Anonymous Call Rejection
Hot line and Warm Line Calling
Speed Dialing of 8 Numbers/Addresses
Music on Hold

SPA3000 Specific
Forward Calls to VoIP service – Selective, Authenticated, All
Forward Calls to PSTN service – Selective, Authenticated, All
PSTN Line Sharing with Multiple Extensions
Automatic PSTN Fallback (Loss of Power or IP Service to Unit – with Quiescence to Normal Operations)
Advanced Inbound and Outbound Call Routing
Single Stage and Two Stage Dialing
Independent Configurable Dial Plans – Up to 8
Force PSTN Disconnection
Sequential Dialing Support

VoIP to PSTN Authentication and Routing
VoIP to PSTN Gateway Enable/Disable
VoIP Caller Auth Method (None, PIN, HTTP Digest)
VoIP PIN Max Retry Setting
One Stage Dialing Enable/Disable
VoIP Caller ID Pattern Matching
VoIP Access Allowed Caller List (No Further Authentication)
VoIP Caller PIN and Associated Dial Plan

PSTN to VoIP Authentication and Features
PSTN to VoIP Gateway Enable/Disable
Caller Auth Method: None, PIN, Caller ID
Ring Through to FXS Enable/Disable
Ring Through Tone – Configurable
Caller ID (Bellcore 1) for VoIP Service Access
Caller ID Enable/Disable
PIN Max Retry Settings
Access Allowed Caller List (No Further Authentication)
Caller PIN and Associated Dial Plan
Least Cost Routing (via Outbound VoIP – Line1 Dial Plan)

International Control
FXO Port Impedance – Configurable to 16 settings
Ring Frequency – Configurable
SPA to PSTN and PSTN to SPA Gain Settings
Ring Frequency – Maximum Setting
Ring Validation Time Setting
Tip/Ring Voltage Adjustment Setting
Ring Indication Delay Setting
Operational Loop Current Minimum Value
Ring Time-out Setting
On-Hook Speed Setting
Ringer Impedance Setting
Line-in-Use Voltage Setting

Security

Password Protected System Reset to Factory Default
Password Protected Admin and User Access Authority
Provisioning/Configuration/Authentication:
HTTP Digest – Encrypted Authentication via MD5 (RFC 1321)
Up to 256-bit AES Encryption

Documentation

Quick-Start Installation and Configuration Guide
User Guide
Administration Guide – Service Providers Only
Provisioning Guide – Service Providers Only

Physical Interfaces:

• 1 10baseT RJ-45 Ethernet Port (IEEE 802.3)
• 1 RJ-11 FXS Phone Ports – For Analog Circuit Telephone Device (Tip/Ring)
• 1 RJ-11 FXO Phone Ports – For a Telco or PBX Connection
• FXS: Subscriber Line Interface Circuit (SLIC):
• Ring Voltage: 40-55 VRMS Configurable l*
• Ring Frequency: 10 Hz – 40 Hz l*
• Ring Waveform: Trapezoidal and Sinusoida l*
• Maximum Ringer Load: 3 REN
• On-hook/off-hook Characteristics:
• On-hook voltage (tip/ring): -50 V NOMINAL
• Off-hook current: 25 mA min
• Terminating Impedance: 8 Configurable Settings including
• North America 600 ohms, European CTR21

Power Supply:

• DC Input Voltage: +5 VDC at 2.0 A Max.
• Power Consumption: 5 Watts
• Switching Type (100-240v) Automatic
• Power Adapter: 100-240v – 50-60Hz (26-34VA) AC Input, 1.8m cord

Package included:

• * 1x Unlocked Linksys SPA3000
• * 1x Universal Power Adaptor (100-240V)
• * 1x RJ-45/RJ11 Cable
• * 1x English Manual